Ghost 2 Immobiliser Reviews
The ghost 2 immobiliser is an innovative anti-theft system that uses advanced technology to prevent car theft. This hidden device is not detected by thieves, and it only starts your engine after a PIN code or app is entered.
It connects to the CAN data network in your vehicle and is weatherproof. It comes with a service/valet feature that lets you temporarily start your car when it is in the garage.
Easy to install
The Ghost immobiliser guards your vehicle from key theft as well as hacking, cloning and stealing. It uses an PIN code system that is integrated into the car's electronic control unit, making it impossible for thieves to recognize. It's not visible and does not use sensors or special keys. It's also less expensive than replacing an ECU or installing a key fob. It can even lower the cost of insurance.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's instructions carefully. This will ensure that the device functions properly and efficiently. Test the system after installation by entering the PIN number and then starting the car. Regular testing will enable you to identify any problems early on.
Check the location of the the CAN H and L wires prior to starting the installation. They are essential to power the immobiliser, so it is essential to ensure that they are connected correctly. It is also recommended to label the wires to make it easier to identify them during the installation process. Once you have identified the locations of these wires and connected them to a permanent 12V power source and an earthing point. Use a fuse tap to shield the connections against short-circuits or damage.
After connecting the wires, tidy the wiring using cable ties to avoid alteration. It is also recommended to cover the wires with insulation tape or heat shrink tubing. This will help protect them from electrical shorts and increase the lifespan of the device. It's a good idea to test your Ghost 2 immobiliser once the wiring is secure.
The Ghost 2 immobiliser offers a service mode for situations in which you may have to give your vehicle away like when it is being serviced or parked by a valet. This disables the PIN sequence for a short period of time. Press the brake pedal and hold the accelerator down for a number of presses equal to the first digit of the emergency code. The system will then enter service mode. This is confirmed by flashing five times the indicator signal.
Easy to change PIN codes
It is simple to secure your vehicle from theft using an immobiliser ghost 2. It is discreetly installed inside the vehicle and can only be accessed using a specific code. The device connects directly to the vehicle ECU via its data bus. It does not rely on radio frequency signals like traditional Thatcham immobilisers, or aftermarket alarm systems. This makes it difficult for thieves to detect the click of an immobiliser relay or to install new key fobs. The control unit is hidden in the wiring of the vehicle or dashboard, and can't be physically tampered to reset the system.
The ghost 2 immobiliser is connected to your vehicle's CAN Data network and uses the buttons already present on the steering wheel, door panels, and the central console to generate a customisable sequence of up to 20 button presses which must be entered before the engine can begin similar to a PIN code. This innovative next-generation system doesn't require any cutting of wires during installation and can be reprogrammed at any time. You can even start your car in either Service or Valet mode after you hand it to a mechanic to do work.
You can also make use of the app to change your PIN number or disable it completely if lost your keys. This feature is especially useful in the event that you've lent your car to someone else to use for valet service or parking. It prevents them from starting it and then driving it off without your permission. It is also undetectable by professional thieves because it doesn't utilize radio frequencies or circuit cuts.
Another great feature of the ghost 2 immobiliser is its capability to prevent relay thefts. Relay theft is a popular method of car theft, where criminals hack into the diagnostic port on your car and then alter the original signal sent by the key to the vehicle's ECU in order to trick it into thinking that there is a valid key. This is how traditional immobilisers can be removed, however with the ghost 2 immobiliser the signal is blocked before it reaches the ECU.
Easy to use app
Ghost 2 is an immobiliser that is revolutionary. It shields your vehicle from key-cloning. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also deters thieves from using signal spoofing or device spoofing, which are common techniques used to steal vehicles.
The system is easy to use and functions like a standard car alarm. Installing the system will allow you to create a unique 20-digit PIN code that you must enter before starting the vehicle. This will prevent the vehicle from being stolen even if your keys are stolen. If you wish to disable the system you can do this by using an app on your smartphone.
The ghost is completely silent and does not emit radio frequency signals. It is a weatherproof, discrete device that can be positioned anywhere in your vehicle. It can be concealed under the dash, the steering wheel, or door panels. It communicates with your ECU through the CAN data circuit, and is not affected by diagnostic tools that some thieves use to find security systems. It is not affected by jamming devices which can spoof codes.
It is a covert system that can be used to stop theft on all vehicles. The technology has been proven efficient, and it is in line with TASSA Standards. The Ghost is a good choice for classic or sports cars. It can be used as a method to safeguard vehicles rented on apps like Turo.
The Autowatch Ghost 2 represents the next generation of auto immobilisers. The system is inaccessible to thieves and blocks them from starting your car unless they have your PIN or are authorised by the app. It does not emit radio frequencies or any other signals that scanners can detect. The installation process is simple and quick. The app is easy to navigate and offers a user-friendly interface which makes it simple to configure and use. It also includes a GPS tracker that can help police locate and locate the vehicle.
Easy to reset
A ghost 2 immobiliser is an excellent method to guard your car from being stolen. car stolen with ghost immobiliser integrates into your vehicle's ECU and creates a security barrier that thieves cannot penetrate without the right pin. The device is TASSA certified which means it's recognized by insurance companies. It is a powerful tool to deter theft of your car and could save you money in the end.
The Ghost system, unlike traditional alarm/immobilisers which require cutting circuits, is directly connected to the vehicle's CAN data network. It works by using the buttons on your dashboard and the steering wheel. You can set up an individual PIN sequence that is up to 20 presses in length. The PIN has to be entered before the engine can begin as it would be a credit card. The Ghost system is completely inaccessible to thieves, and there are no LEDs to indicate its presence. This makes it the most efficient aftermarket CAN-bus immobiliser available today.
The Ghost system also has a benefit that it doesn't transmit radio frequency signals. This means that it is not stolen or scanned by thieves. This stops cloned key attacks and relay attacks, as and the typical method of hacking into a car's computer system using its CAN bus by scanning for signals. Additionally, the Ghost system is designed to be completely hidden in your vehicle. There aren't any lights or signals to indicate its presence.
The system features an option called Transport Mode that disables the Ghost System. This is useful for situations when you require a temporary deactivation of Ghost for instance, when you are transporting or servicing your vehicle. However, this mode is not as effective as Service Mode, as it does not deactivate the system when your vehicle speeds over 31 mph for fifteen minutes.
To reset your ghost 2 immobiliser, you'll need the emergency code, which is available from your installer. It is usually hidden under an area for scratch-offs on the card that was included with the installation. This emergency code should be secured and stored in a secure location, such as an at-home wallet.